Epson
t0715 and
t0711 compatible
cartridges
Suitable for printers: Epson Stylus
D78/D92/DX7000F/DX5000/DX4050/4000/4400/4450/DX5050/DX6000 Epson
Stylus DX6050/DX7400/DX7450/DX8400/DX8450/DX9400/DX9400F
Epson Stylus S20/S21
Epson Stylus SX100/SX110/SX200/SX209/SX210/SX400/SX510W Epson
Stylus SX410/SX610FW/SX600FW/SX205/SX215/SX105/SX405
Epson Stylus BX310FN/BX300F/BX3450F/BX600FW/BX610FW/B40W
Compatible
Epson T0715 Ink
Cartridges normally is produced by some third parties, not original
manufacturer. But the products can work well in the same way as OEM
cartridges. Meanwhile, the price is much lower than the OEM
ones.
Will compatible cartridges damage my printer?
Don't worry, the manufacturer already made strict compatibility
testing for us and the ink of the
Epson t0711 Ink
Cartridges is made in USA. As long as following the compatible
printer list we provide, there should be no problem.
Epson printer maintenance Sourcebook
The ink machine lights flashing approach
Hold the ink button and paper feed button on the control panel
then power 3 seconds after boot, hand feed button immediately
release the pressing for about 10 seconds, then the ink key hand
after three lights flash again, then hands off, so that we can ROM
Qing, the motherboard on OK. The role of this operation is to clear
the waste ink counter. In addition, the adjustment procedure can
also achieve this purpose. If two years ago to encounter this three
lights flash failure all change the motherboard, to the later to
further repair the motherboard, now just few clicks OK in the
Control Panel This shows that repair printers have the experience
and patience to troubleshoot. The print head cable disconnection
fault of the print head cables are generally plastic flexible
ribbon cable. This cable during use, easy to produce crease, a
socket end of the cable is inserted in the print head, in the
crease at the fracture occurs with the increase in print head
mating cycles (Repair when the print head is split below);
Another is as the printing time increases, the intermediate
portion of the print cable easily during the move of the word car
is worn or creased. The cable insulation layer is worn away, would
print the the needle drive signal with the printer rack short
circuit, lead the printer master circuit failure; print cable
crease at the fracture will open print pin drive signal, causing
the corresponding print needle the no pin print, resulting in less
printable characters / kanji shortcomings program.
Both cable fault can be checked with a multimeter. The method is
to take two table pen multimeter corresponding line in the ends of
the cable, the amount of resistance is zero, if necessary, in the
crease bending test, observe whether the multimeter on the
resistance change. Can be diagnosed broken cable replacement print
head using the same models. Keep in mind that the cable breaks can
not be handled by welding, because it will appear in the course of
the signal short treatment of severe will result in
signal-to-ground short circuit, causing the printer's main control
circuit malfunction.
Crease in the print head cable, but at the end is broken, to
take preventive measures to avoid the break of signal line. : The
first cut-off period of about 1.5cm adhesive tape, followed by an
approximately o 5cm width and viscose width same tissue paper
pieces attached to the middle of the tape to avoid tape Central
cable sticky together. And then so that the cable in the crease at
the slightly bent outwardly, so that the sheets positive crease the
tape to the cable. In this way, the tension generated by the tape
sheet will always force the cable in the crease at slightly
outwardly curved, so that the cable in the crease at an outwardly
suitable tension, which can reliably avoid the rightward movement
of the print head during the printing process causing the cable at
the crease at the fold volumes to prevent the print head cable
signal line break.
The EPSON inkjet machine cleared the models divided into the
following categories:
1.480,580, C20, C40, C41 Series online display unknown error,
can be cleared when the service request or the printer is turned on
after the power light and the lights flash alternately feed. The
run cleared after online software interface first select the
appropriate option click "OK" to enter the program prompted frame
ignore click "close", then enter the main interface, click on the
left "Maintenance (maintenance)" tab, click "protect counter check
(counter check)" in its right side has an option to clear the
protect counter values ??(Clear counter value), click below the
"OK" button is selected to perform operations. At this time, please
pay attention to the status bar below. "The protect counter has
been initialzed (counter has been initialized)." Software prompts
takes 30 seconds to initialize the printer, Next, according to the
prompts. Note that if the in the initialization printer process,
the printer is not responding, the word car no action, you need to
restart the software.
2.680,790,830, C60, C80, 870,1290 series several models which
can use a software clear also available printers panel completed
the panel cleared Reference entry.
3.700,710,720, EX, EX2, EX3, 1200,1270 series of several series
of three-button machine failure phenomenon to power lights and
other lights flash alternately, and the other two lights the same
frequency. Press the FEED button and cleaning key (individual
machine change ink key) boot release the feed button after two
seconds, two seconds later release the cleaning button, then hold
down the cleaning button until all the lights light at the same
time, the word car action, release the key. 4.1500K, 1500K, 1520K
multi-key machine series EPSON A3 EPSON STYLUS COLOR 1500K and
EPSON STYLUS COLOR 1520K both. 1520K boot print documents, the
printer suddenly issued a burst of "terrorist" sound, followed by
all shiny red on the right side of the printer panel, no print head
ink action, the machine can not print any text and image, the
printer paralyzed . The EPSON inside the printer has a counter, ink
the number of records Motou. Counter to a certain value, it is
necessary to clean the ink sponge and the loaded run out of ink
cartridges, then the counter is cleared to. Counter clear: hold
down the "Alt" key, "wrap / paging key" feed / Eject "key," font
"key four-button, power on, hear an audible" beep "after the
machine back work properly. EPSON 1520 cleared hold down the "Alt"
key, "wrap / Page" key "feed / Eject" key, "font" key four-button,
power on, you hear the "beep" sound, the machine back to normal
job.