Epson printer maintenance Sourcebook

Epson t0715 and t0711 compatible cartridges

Suitable for printers: Epson Stylus D78/D92/DX7000F/DX5000/DX4050/4000/4400/4450/DX5050/DX6000 Epson Stylus DX6050/DX7400/DX7450/DX8400/DX8450/DX9400/DX9400F

Epson Stylus S20/S21

Epson Stylus SX100/SX110/SX200/SX209/SX210/SX400/SX510W Epson Stylus SX410/SX610FW/SX600FW/SX205/SX215/SX105/SX405

Epson Stylus BX310FN/BX300F/BX3450F/BX600FW/BX610FW/B40W

Compatible Epson T0715 Ink Cartridges normally is produced by some third parties, not original manufacturer. But the products can work well in the same way as OEM cartridges. Meanwhile, the price is much lower than the OEM ones.

Will compatible cartridges damage my printer?

Don't worry, the manufacturer already made strict compatibility testing for us and the ink of the Epson t0711 Ink Cartridges is made in USA. As long as following the compatible printer list we provide, there should be no problem.

Epson printer maintenance Sourcebook

The ink machine lights flashing approach

Hold the ink button and paper feed button on the control panel then power 3 seconds after boot, hand feed button immediately release the pressing for about 10 seconds, then the ink key hand after three lights flash again, then hands off, so that we can ROM Qing, the motherboard on OK. The role of this operation is to clear the waste ink counter. In addition, the adjustment procedure can also achieve this purpose. If two years ago to encounter this three lights flash failure all change the motherboard, to the later to further repair the motherboard, now just few clicks OK in the Control Panel This shows that repair printers have the experience and patience to troubleshoot. The print head cable disconnection fault of the print head cables are generally plastic flexible ribbon cable. This cable during use, easy to produce crease, a socket end of the cable is inserted in the print head, in the crease at the fracture occurs with the increase in print head mating cycles (Repair when the print head is split below);

Another is as the printing time increases, the intermediate portion of the print cable easily during the move of the word car is worn or creased. The cable insulation layer is worn away, would print the the needle drive signal with the printer rack short circuit, lead the printer master circuit failure; print cable crease at the fracture will open print pin drive signal, causing the corresponding print needle the no pin print, resulting in less printable characters / kanji shortcomings program.

Both cable fault can be checked with a multimeter. The method is to take two table pen multimeter corresponding line in the ends of the cable, the amount of resistance is zero, if necessary, in the crease bending test, observe whether the multimeter on the resistance change. Can be diagnosed broken cable replacement print head using the same models. Keep in mind that the cable breaks can not be handled by welding, because it will appear in the course of the signal short treatment of severe will result in signal-to-ground short circuit, causing the printer's main control circuit malfunction.

Crease in the print head cable, but at the end is broken, to take preventive measures to avoid the break of signal line. : The first cut-off period of about 1.5cm adhesive tape, followed by an approximately o 5cm width and viscose width same tissue paper pieces attached to the middle of the tape to avoid tape Central cable sticky together. And then so that the cable in the crease at the slightly bent outwardly, so that the sheets positive crease the tape to the cable. In this way, the tension generated by the tape sheet will always force the cable in the crease at slightly outwardly curved, so that the cable in the crease at an outwardly suitable tension, which can reliably avoid the rightward movement of the print head during the printing process causing the cable at the crease at the fold volumes to prevent the print head cable signal line break.

The EPSON inkjet machine cleared the models divided into the following categories:

1.480,580, C20, C40, C41 Series online display unknown error, can be cleared when the service request or the printer is turned on after the power light and the lights flash alternately feed. The run cleared after online software interface first select the appropriate option click "OK" to enter the program prompted frame ignore click "close", then enter the main interface, click on the left "Maintenance (maintenance)" tab, click "protect counter check (counter check)" in its right side has an option to clear the protect counter values ??(Clear counter value), click below the "OK" button is selected to perform operations. At this time, please pay attention to the status bar below. "The protect counter has been initialzed (counter has been initialized)." Software prompts takes 30 seconds to initialize the printer, Next, according to the prompts. Note that if the in the initialization printer process, the printer is not responding, the word car no action, you need to restart the software.

2.680,790,830, C60, C80, 870,1290 series several models which can use a software clear also available printers panel completed the panel cleared Reference entry.

3.700,710,720, EX, EX2, EX3, 1200,1270 series of several series of three-button machine failure phenomenon to power lights and other lights flash alternately, and the other two lights the same frequency. Press the FEED button and cleaning key (individual machine change ink key) boot release the feed button after two seconds, two seconds later release the cleaning button, then hold down the cleaning button until all the lights light at the same time, the word car action, release the key. 4.1500K, 1500K, 1520K multi-key machine series EPSON A3 EPSON STYLUS COLOR 1500K and EPSON STYLUS COLOR 1520K both. 1520K boot print documents, the printer suddenly issued a burst of "terrorist" sound, followed by all shiny red on the right side of the printer panel, no print head ink action, the machine can not print any text and image, the printer paralyzed . The EPSON inside the printer has a counter, ink the number of records Motou. Counter to a certain value, it is necessary to clean the ink sponge and the loaded run out of ink cartridges, then the counter is cleared to. Counter clear: hold down the "Alt" key, "wrap / paging key" feed / Eject "key," font "key four-button, power on, hear an audible" beep "after the machine back work properly. EPSON 1520 cleared hold down the "Alt" key, "wrap / Page" key "feed / Eject" key, "font" key four-button, power on, you hear the "beep" sound, the machine back to normal job.